.\" manual page [] for pppd 2.3
-.\" $Id: pppd.8,v 1.36 1999/03/22 05:55:34 paulus Exp $
+.\" $Id: pppd.8,v 1.45 1999/08/13 13:42:35 johnsonm Exp $
.\" SH section heading
.\" SS subsection heading
.\" LP paragraph
Read options from file \fIname\fR (the format is described below).
The file must be readable by the user who has invoked pppd.
.TP
+.B init \fIscript
+Run the executable or shell command specified by \fIscript\fR to
+initialize the serial line. This script would typically use the
+chat(8) program to configure the modem to enable auto answer. A value
+for this option from a privileged source cannot be overridden by a
+non-privileged user.
+.TP
.B lock
Specifies that pppd should create a UUCP-style lock file for the
serial device to ensure exclusive access to the device.
Set the LCP restart interval (retransmission timeout) to \fIn\fR
seconds (default 3).
.TP
+.B linkname \fIname\fR
+Sets the logical name of the link to \fIname\fR. Pppd will create a
+file named \fBppp-\fIname\fB.pid\fR in /var/run (or /etc/ppp on some
+systems) containing its process ID. This can be useful in determining
+which instance of pppd is responsible for the link to a given peer
+system. This is a privileged option.
+.TP
.B local
Don't use the modem control lines. With this option, pppd will ignore
the state of the CD (Carrier Detect) signal from the modem and will
not change the state of the DTR (Data Terminal Ready) signal.
.TP
+.B logfd \fIn
+Send log messages to file descriptor \fIn\fR. Pppd will send log
+messages to at most one file or file descriptor (as well as sending
+the log messages to syslog), so this option and the \fBlogfile\fR
+option are mutually exclusive. The default is for pppd to send log
+messages to stdout (file descriptor 1), unless the serial port is
+already open on stdout.
+.TP
+.B logfile \fIfilename
+Append log messages to the file \fIfilename\fR (as well as sending the
+log messages to syslog). The file is opened with the privileges of
+the user who invoked pppd, in append mode.
+.TP
.B login
Use the system password database for authenticating the peer using
PAP, and record the user in the system wtmp file. Note that the peer
traffic for \fIn\fR seconds (i.e. \fIn\fR seconds after the first
network control protocol comes up).
.TP
+.B maxfail \fIn
+Terminate after \fIn\fR consecutive failed connection attempts. A
+value of 0 means no limit. The default value is 10.
+.TP
.B modem
Use the modem control lines. This option is the default. With this
option, pppd will wait for the CD (Carrier Detect) signal from the
required if the peer is buggy and gets confused by requests from pppd
for IPXCP negotiation.
.TP
+.B nolog
+Do not send log messages to a file or file descriptor. This option
+cancels the \fBlogfd\fR and \fBlogfile\fR options.
.B nomagic
Disable magic number negotiation. With this option, pppd cannot
detect a looped-back line. This option should only be needed if the
specified.
.TP
.B nopredictor1
-Do not accept or agree to Predictor-1 comprssion.
+Do not accept or agree to Predictor-1 compression.
.TP
.B noproxyarp
Disable the \fIproxyarp\fR option. The system administrator who
option, pppd will discard those characters as specified in RFC1662.
This option should only be needed if the peer is buggy.
.TP
+.B record \fIfilename
+Specifies that pppd should record all characters sent and received to
+a file named \fIfilename\fR. This file is opened in append mode,
+using the user's user-ID and permissions. This option is implemented
+using a pseudo-tty and a process to transfer characters between the
+pseudo-tty and the real serial device, so it will increase the latency
+and CPU overhead of transferring data over the ppp interface. The
+characters are stored in a tagged format with timestamps, which can be
+displayed in readable form using the pppdump(8) program.
+.TP
.B remotename \fIname
Set the assumed name of the remote system for authentication purposes
to \fIname\fR.
connection until a valid LCP packet is received from the peer (as for
the `passive' option with ancient versions of pppd).
.TP
+.B sync
+Use synchronous HDLC serial encoding instead of asynchronous.
+The device used by pppd with this option must have sync support.
+Currently supports Microgate SyncLink adapters
+under Linux and FreeBSD 2.2.8 and later.
+.TP
+.B updetach
+With this option, pppd will detach from its controlling terminal once
+it has successfully established the ppp connection (to the point where
+the first network control protocol, usually the IP control protocol,
+has come up).
+.TP
.B usehostname
Enforce the use of the hostname (with domain name appended, if given)
as the name of the local system for authentication purposes (overrides
the \fIname\fR option). This option is not normally needed since the
\fIname\fR option is privileged.
.TP
+.B usepeerdns
+Ask the peer for up to 2 DNS server addresses. The addresses supplied
+by the peer (if any) are passed to the /etc/ppp/ip-up script in the
+environment variables DNS1 and DNS2.
+.TP
.B user \fIname
Sets the name used for authenticating the local system to the peer to
\fIname\fR.
.LP
Debugging can also be enabled or disabled by sending a SIGUSR1 signal
to the pppd process. This signal acts as a toggle.
+.SH EXIT STATUS
+The exit status of pppd is set to indicate whether any error was
+detected, or the reason for the link being terminated. The values
+used are:
+.TP
+.B 0
+Pppd has detached, or otherwise the connection was successfully
+established and terminated at the peer's request.
+.TP
+.B 1
+An immediately fatal error of some kind occurred, such as an essential
+system call failing, or running out of virtual memory.
+.TP
+.B 2
+An error was detected in processing the options given, such as two
+mutually exclusive options being used.
+.TP
+.B 3
+Pppd is not setuid-root and the invoking user is not root.
+.TP
+.B 4
+The kernel does not support PPP, for example, the PPP kernel driver is
+not included or cannot be loaded.
+.TP
+.B 5
+Pppd terminated because it was sent a SIGINT, SIGTERM or SIGHUP
+signal.
+.TP
+.B 6
+The serial port could not be locked.
+.TP
+.B 7
+The serial port could not be opened.
+.TP
+.B 8
+The connect script failed (returned a non-zero exit status).
+.TP
+.B 9
+The command specified as the argument to the \fIpty\fR option could
+not be run.
+.TP
+.B 10
+The PPP negotiation failed, that is, it didn't reach the point where
+at least one network protocol (e.g. IP) was running.
+.TP
+.B 11
+The peer system failed (or refused) to authenticate itself.
+.TP
+.B 12
+The link was established successfully and terminated because it was
+idle.
+.TP
+.B 13
+The link was established successfully and terminated because the
+connect time limit was reached.
+.TP
+.B 14
+Callback was negotiated and an incoming call should arrive shortly.
+.TP
+.B 15
+The link was terminated because the peer is not responding to echo
+requests.
+.TP
+.B 16
+The link was terminated by the modem hanging up.
+.TP
+.B 17
+The PPP negotiation failed because serial loopback was detected.
+.TP
+.B 18
+The init script failed (returned a non-zero exit status).
+.TP
+.B 19
+We failed to authenticate ourselves to the peer.
.SH SCRIPTS
Pppd invokes scripts at various stages in its processing which can be
used to perform site-specific ancillary processing. These scripts are
.TP
.B ORIG_UID
The real user-id of the user who invoked pppd.
+.TP
+.B PPPLOGNAME
+The username of the real user-id that invoked pppd. This is always set.
+.P
+For the ip-down and auth-down scripts, pppd also sets the following
+variables giving statistics for the connection:
+.TP
+.B CONNECT_TIME
+The number of seconds from when the PPP negotiation started until the
+connection was terminated.
+.TP
+.B BYTES_SENT
+The number of bytes sent (at the level of the serial port) during the
+connection.
+.TP
+.B BYTES_RCVD
+The number of bytes received (at the level of the serial port) during
+the connection.
+.TP
+.B LINKNAME
+The logical name of the link, set with the \fIlinkname\fR option.
.P
Pppd invokes the following scripts, if they exist. It is not an error
if they don't exist.
.B /var/run/ppp\fIn\fB.pid \fR(BSD or Linux), \fB/etc/ppp/ppp\fIn\fB.pid \fR(others)
Process-ID for pppd process on ppp interface unit \fIn\fR.
.TP
+.B /var/run/ppp-\fIname\fB.pid \fR(BSD or Linux), \fB/etc/ppp/ppp-\fIname\fB.pid \fR(others)
+Process-ID for pppd process for logical link \fIname\fR (see the
+\fIlinkname\fR option).
+.TP
.B /etc/ppp/pap-secrets
Usernames, passwords and IP addresses for PAP authentication. This
file should be owned by root and not readable or writable by any other
projects / ppp.git / blobdiff