compression in the corresponding direction. Use \fInobsdcomp\fR or
\fIbsdcomp 0\fR to disable BSD-Compress compression entirely.
.TP
+.B ca \fIca-file
+(EAP-TLS) Use the file \fIca-file\fR as the X.509 Certificate Authority
+(CA) file (in PEM format), needed for setting up an EAP-TLS connection.
+This option is used on the client-side in conjunction with the \fBcert\fR
+and \fBkey\fR options.
+.TP
.B cdtrcts
Use a non-standard hardware flow control (i.e. DTR/CTS) to control
the flow of data on the serial port. If neither the \fIcrtscts\fR,
bi-directional flow control. The sacrifice is that this flow
control mode does not permit using DTR as a modem control line.
.TP
+.B cert \fIcertfile
+(EAP-TLS) Use the file \fIcertfile\fR as the X.509 certificate (in PEM
+format), needed for setting up an EAP-TLS connection. This option is
+used on the client-side in conjunction with the \fBca\fR and
+\fBkey\fR options.
+.TP
.B chap\-interval \fIn
If this option is given, pppd will rechallenge the peer every \fIn\fR
seconds.
1000 (1 second). This wait period only applies if the \fBconnect\fR
or \fBpty\fR option is used.
.TP
+.B crl \fIfilename
+(EAP-TLS) Use the file \fIfilename\fR as the Certificate Revocation List
+to check for the validity of the peer's certificate. This option is not
+mandatory for setting up an EAP-TLS connection. Also see the \fBcrl-dir\fR
+option.
+.TP
+.B crl-dir \fIdirectory
+(EAP-TLS) Use the directory \fIdirectory\fR to scan for CRL files in
+has format ($hash.r0) to check for the validity of the peer's certificate.
+This option is not mandatory for setting up an EAP-TLS connection.
+Also see the \fBcrl\fR option.
+.TP
.B debug
Enables connection debugging facilities.
If this option is given, pppd will log the contents of all
interface identifier, even if the local IPv6 interface identifier
was specified in an option.
.TP
+.B ipv6cp\-accept\-remote
+With this option, pppd will accept the peer's idea of its (remote)
+IPv6 interface identifier, even if the remote IPv6 interface
+identifier was specified in an option.
+.TP
.B ipv6cp\-max\-configure \fIn
Set the maximum number of IPv6CP configure-request transmissions to
\fIn\fR (default 10).
the kernel are logged by syslog(1) to a file as directed in the
/etc/syslog.conf configuration file.
.TP
+.B key \fIkeyfile
+(EAP-TLS) Use the file \fIkeyfile\fR as the private key file (in PEM
+format), needed for setting up an EAP-TLS connection. This option is
+used on the client-side in conjunction with the \fBca\fR and
+\fBcert\fR options.
+.TP
.B ktune
Enables pppd to alter kernel settings as appropriate. Under Linux,
pppd will enable IP forwarding (i.e. set /proc/sys/net/ipv4/ip_forward
dynamic IP address option (i.e. set /proc/sys/net/ipv4/ip_dynaddr to
1) in demand mode if the local address changes.
.TP
+.B lcp\-echo\-adaptive
+If this option is used with the \fIlcp\-echo\-failure\fR option then
+pppd will send LCP echo\-request frames only if no traffic was received
+from the peer since the last echo\-request was sent.
+.TP
.B lcp\-echo\-failure \fIn
If this option is given, pppd will presume the peer to be dead
if \fIn\fR LCP echo\-requests are sent without receiving a valid LCP
Disable Address/Control compression in both directions (send and
receive).
.TP
+.B need-peer-eap
+(EAP-TLS) Require the peer to verify our authentication credentials.
+.TP
.B noauth
Do not require the peer to authenticate itself. This option is
privileged.
stored in ~/.ppp_pseudonym first as the identity, and save in this
file any pseudonym offered by the peer during authentication.
.TP
+.B stop\-bits \fIn
+Set the number of stop bits for the serial port. Valid values are 1 or 2.
+The default value is 1.
+.TP
.B sync
Use synchronous HDLC serial encoding instead of asynchronous.
The device used by pppd with this option must have sync support.
.I PPP in HDLC-like Framing.
July 1994.
.TP
+.B RFC1990
+Sklower, K.; et al.,
+.I The PPP Multilink Protocol (MP).
+August 1996.
+.TP
.B RFC2284
Blunk, L.; Vollbrecht, J.,
.I PPP Extensible Authentication Protocol (EAP).