omitted. The identifier must be specified in standard ASCII notation of
IPv6 addresses (e.g. ::dead:beef). If the
\fIipv6cp\-use\-ipaddr\fR
-option is given, the local identifier is the local IPv4 address (see above).
+option is given, the local identifier is the local IPv4 address and the
+remote identifier is the remote IPv4 address (see above).
+If the \fIipv6cp-use-remotenumber\fR option is given, the remote identifier
+is set to the value from \fIremotenumber\fR option.
On systems which supports a unique persistent id, such as EUI\-48 derived
from the Ethernet MAC address, \fIipv6cp\-use\-persistent\fR option can be
-used to replace the \fIipv6 <local>,<remote>\fR option. Otherwise the
-identifier is randomized.
+used to set local identifier. Otherwise both local and remote identifiers
+are randomized.
.TP
.B active\-filter \fIfilter\-expression
Specifies a packet filter to be applied to data packets to determine
IPv6 interface identifier, even if the remote IPv6 interface
identifier was specified in an option.
.TP
+.B ipv6cp\-noremote
+Allow pppd to operate without having an IPv6 link local address for the peer.
+This option is only available under Linux. Normally, pppd will request the
+peer's IPv6 interface identifier (used for composing IPv6 link local address),
+and if the peer does not supply it, pppd will generate one for the peer.
+With this option, if the peer does not supply its IPv6 interface identifier,
+pppd will not ask the peer for it, and will not set the destination IPv6
+link local address of the ppp interface. In this situation, the ppp interface
+can be used for routing by creating device routes, but the peer itself cannot
+be addressed directly for IPv6 traffic until the peer starts announcing ICMPv6
+Router Advertisement or ICMPv6 Neighbor Advertisement packets. Note that IPv6
+router must announce ICMPv6 Router Advertisement packets.
+.TP
+.B ipv6cp\-nosendip
+Don't send our local IPv6 interface identifier to peer during IPv6 interface
+identifier negotiation.
+.TP
.B ipv6cp\-max\-configure \fIn
Set the maximum number of IPv6CP configure-request transmissions to
\fIn\fR (default 10).
/etc/ppp/resolv.conf file containing one or two nameserver lines with
the address(es) supplied by the peer.
.TP
+.B usepeerwins
+Ask the peer for up to 2 WINS server addresses. The addresses supplied
+by the peer (if any) are passed to the /etc/ppp/ip\-up script in the
+environment variables WINS1 and WINS2, and the environment variable
+USEPEERWINS will be set to 1.
+.LP
+Please note that some modems (like the Huawei E220) requires this option in
+order to avoid a race condition that results in the incorrect DNS servers
+being assigned.
+.TP
.B user \fIname
Sets the name used for authenticating the local system to the peer to
\fIname\fR.
\fBrp_pppoe_sess\fP option name is supported.
.TP
.B pppoe-verbose \fIn
-Be verbose about discovered access concentrators. For backward
-compatibility also \fBrp_pppoe_verbose\fP option name is supported.
+Be verbose about discovered access concentrators. When set to 2 or bigger
+value then dump also discovery packets. For backward compatibility also
+\fBrp_pppoe_verbose\fP option name is supported.
.TP
.B pppoe-mac \fImacaddr
Connect to specified MAC address.
If the peer supplies DNS server addresses, this variable is set to the
second DNS server address supplied (whether or not the usepeerdns
option was given).
+.TP
+.B WINS1
+If the peer supplies WINS server addresses, this variable is set to the
+first WINS server address supplied.
+.TP
+.B WINS2
+If the peer supplies WINS server addresses, this variable is set to the
+second WINS server address supplied.
+.P
.P
Pppd invokes the following scripts, if they exist. It is not an error
if they don't exist.
projects / ppp.git / blobdiff