# /etc/ppp/options # The name of this server. Often, the FQDN is used here. #name # Enforce the use of the hostname as the name of the local system for # authentication purposes (overrides the name option). usehostname # If no local IP address is given, pppd will use the first IP address # that belongs to the local hostname. If "noipdefault" is given, this # is disabled and the peer will have to supply an IP address. noipdefault # With this option, pppd will accept the peer's idea of our local IP # address, even if the local IP address was specified in an option. #ipcp-accept-local # With this option, pppd will accept the peer's idea of its (remote) IP # address, even if the remote IP address was specified in an option. #ipcp-accept-remote # Specify which DNS Servers the incoming Win95 or WinNT Connection should use # Two Servers can be remotely configured #ms-dns 192.168.1.1 #ms-dns 192.168.1.2 # Specify which WINS Servers the incoming connection Win95 or WinNT should use #wins-addr 192.168.1.50 #wins-addr 192.168.1.51 # enable this on a server that already has a permanent default route #nodefaultroute # Default IPv6 route is automatically configured by kernel based on # received ICMPv6 Router Advertisement packets. # pppd should not touch default IPv6 route to prevent breaking IPv6 setup. # Enabling defaultroute6 is needed only for broken IPv6 setup. nodefaultroute6 # Run the executable or shell command specified after pppd has terminated # the link. This script could, for example, issue commands to the modem # to cause it to hang up if hardware modem control signals were not # available. # If mgetty is running, it will reset the modem anyway. So there is no need # to do it here. #disconnect "chat -- \d+++\d\c OK ath0 OK" # Increase debugging level (same as -d). The debug output is written # to syslog LOG_LOCAL2. debug # Enable debugging code in the kernel-level PPP driver. The argument n # is a number which is the sum of the following values: 1 to enable # general debug messages, 2 to request that the contents of received # packets be printed, and 4 to request that the contents of transmitted # packets be printed. #kdebug n # Require the peer to authenticate itself before allowing network # packets to be sent or received. # Please do not disable this setting. It is expected to be standard in # future releases of pppd. Use the call option (see manpage) to disable # authentication for specific peers. #auth # authentication can either be pap or chap. As most people only want to # use pap, you can also disable chap: #require-pap #refuse-chap # Use hardware flow control (i.e. RTS/CTS) to control the flow of data # on the serial port. crtscts # Specifies that pppd should use a UUCP-style lock on the serial device # to ensure exclusive access to the device. lock # Use the modem control lines. modem # async character map -- 32-bit hex; each bit is a character # that needs to be escaped for pppd to receive it. 0x00000001 # represents '\x01', and 0x80000000 represents '\x1f'. # To allow pppd to work over a rlogin/telnet connection, ou should escape # XON (^Q), XOFF (^S) and ^]: (The peer should use "escape ff".) #asyncmap 200a0000 asyncmap 0 # Specifies that certain characters should be escaped on transmission # (regardless of whether the peer requests them to be escaped with its # async control character map). The characters to be escaped are # specified as a list of hex numbers separated by commas. Note that # almost any character can be specified for the escape option, unlike # the asyncmap option which only allows control characters to be # specified. The characters which may not be escaped are those with hex # values 0x20 - 0x3f or 0x5e. #escape 11,13,ff # Set the MRU [Maximum Receive Unit] value to for negotiation. pppd # will ask the peer to send packets of no more than bytes. The # minimum MRU value is 128. The default MRU value is 1500. A value of # 296 is recommended for slow links (40 bytes for TCP/IP header + 256 # bytes of data). #mru 542 # Set the MTU [Maximum Transmit Unit] value to . Unless the peer # requests a smaller value via MRU negotiation, pppd will request that # the kernel networking code send data packets of no more than n bytes # through the PPP network interface. #mtu # Set the interface netmask to , a 32 bit netmask in "decimal dot" # notation (e.g. 255.255.255.0). #netmask 255.255.255.0 # Don't fork to become a background process (otherwise pppd will do so # if a serial device is specified). nodetach # Set the assumed name of the remote system for authentication purposes # to . #remotename # Add an entry to this system's ARP [Address Resolution Protocol] # table with the IP address of the peer and the Ethernet address of this # system. {proxyarp,noproxyarp} proxyarp # Use the system password database for authenticating the peer using # PAP. Note: mgetty already provides this option. If this is specified # then dialin from users using a script under Linux to fire up ppp wont work. #login # If this option is given, pppd will send an LCP echo-request frame to # the peer every n seconds. Under Linux, the echo-request is sent when # no packets have been received from the peer for n seconds. Normally # the peer should respond to the echo-request by sending an echo-reply. # This option can be used with the lcp-echo-failure option to detect # that the peer is no longer connected. lcp-echo-interval 30 # If this option is given, pppd will presume the peer to be dead if n # LCP echo-requests are sent without receiving a valid LCP echo-reply. # If this happens, pppd will terminate the connection. Use of this # option requires a non-zero value for the lcp-echo-interval parameter. # This option can be used to enable pppd to terminate after the physical # connection has been broken (e.g., the modem has hung up) in # situations where no hardware modem control lines are available. lcp-echo-failure 4 # Specifies that pppd should disconnect if the link is idle for n seconds. idle 600 # ------