See the man page for ip(7p) for details.
+Dynamic STREAMS Re-Plumbing Support.
+************************************
+
+Solaris 8 includes dynamic re-plumbing support. With this, modules below ip can
+be inserted, or removed, without having the ip stream be unplumbed, and re-
+plumbed again. All states in ip for an interface will therefore now be
+preserved. Users can install (or upgrade) modules like firewall, bandwidth
+manager, cache manager, tunneling, etc., without shutting the machine down.
+
+To support this, ppp driver now uses /dev/udp instead of /dev/ip for
+the ip stream. The interface stream (where ip module pushed on top of ppp)
+is then I_PLINK'ed below the ip stream. /dev/udp is used because STREAMS will
+not let a driver be PLINK'ed under itself, and /dev/ip is typically the driver
+at the bottom of the tunneling interfaces stream. The mux ids of the ip
+streams are then added using SIOCSxIFMUXID ioctl.
+
+Users will be able to see the modules on the insterface stream by, for example:
+
+ pikapon% ifconfig ppp modlist
+ 0 ip
+ 1 ppp
+
+Or arbitrarily if bandiwth manager and firewall modules are installed:
+
+ pikapon% ifconfig hme0 modlist
+ 0 arp
+ 1 ip
+ 2 ipqos
+ 3 firewall
+ 4 hme
+
+Snoop Support.
+**************
+
+This version includes support for /usr/sbin/snoop. Tests has been done on both
+Solaris 7 and 8. Only IPv4 and IPv6 packets will be sent up to stream(s) marked
+as promiscuous, e.g, snoop et al.
+
+Users will be able to see the packets on the ppp interface by, for example:
+
+ snoop -d ppp0
+
+See the man page for snoop(1M) for details.
+
+IPv6 Support.
+*************
+
+This is for Solaris 8 and later.
+
+This version has been tested under Solaris 8 running IPv6. As of now,
+interoperability testing has only been done between Solaris machines in terms
+of the IPV6 NCP. An additional command line option for the pppd daemon has
+been added: ipv6cp-use-persistent
+
+By default, compilation for IPv6 support is not enabled. Uncomment the
+necessary lines in pppd/Makefile.sol2 to enable it. Once done, the quickest way
+to get IPv6 running is to add the following somewhere in the command line
+option:
+
+ +ipv6 ipv6cp-use-persistent
+
+The persistent id for the link-local address was added to conform to RFC 2472;
+such that if there's an EUI-48 available, use that to make up the EUI-64. As of
+now, the Solaris implementation extracts the EUI-48 id from the Ethernet's MAC
+address (the ethernet interface needs to be up). Future works might support
+other ways of obtaining a unique yet persistent id, such as EEPROM serial
+numbers, etc.
+
+There need not be any up/down scripts for ipv6, e.g. /etc/ppp/ipv6-up or
+/etc/ppp/ipv6-down, to trigger IPv6 neighbor discovery for auto configuration
+and routing. The in.ndpd daemon will perform all of the necessary jobs in the
+background. /etc/inet/ndpd.conf can be further customized to enable the machine
+as an IPv6 router. See the man page for in.ndpd(1M) and ndpd.conf(4) for
+details.
+
+Below is a sample output of "ifconfig -a" with persistent link-local address.
+Note the UNNUMBERED flag is set because hme0 and ppp0 both have identical
+link-local IPv6 addresses:
+
+lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
+ inet 127.0.0.1 netmask ff000000
+hme0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
+ inet 129.146.86.248 netmask ffffff00 broadcast 129.146.86.255
+ ether 8:0:20:8d:38:c1
+lo0: flags=2000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6> mtu 8252 index 1
+ inet6 ::1/128
+hme0: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
+ ether 8:0:20:8d:38:c1
+ inet6 fe80::a00:20ff:fe8d:38c1/10
+hme0:1: flags=2080841<UP,RUNNING,MULTICAST,ADDRCONF,IPv6> mtu 1500 index 2
+ inet6 fec0::56:a00:20ff:fe8d:38c1/64
+hme0:2: flags=2080841<UP,RUNNING,MULTICAST,ADDRCONF,IPv6> mtu 1500 index 2
+ inet6 2000::56:a00:20ff:fe8d:38c1/64
+hme0:3: flags=2080841<UP,RUNNING,MULTICAST,ADDRCONF,IPv6> mtu 1500 index 2
+ inet6 2::56:a00:20ff:fe8d:38c1/64
+ppp0: flags=10008d1<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST,IPv4> mtu 1500 index 12
+ inet 172.16.1.1 --> 172.16.1.2 netmask ffffff00
+ppp0: flags=2202851<UP,POINTOPOINT,RUNNING,MULTICAST,UNNUMBERED,NONUD,IPv6> mtu 1500 index 12
+ inet6 fe80::a00:20ff:fe8d:38c1/10 --> fe80::a00:20ff:fe7a:24fb
+
+Note also that a plumbed ipv6 interface stream will exist throughout the entire
+PPP session in the case where the peer rejects IPV6CP, which further causes the
+interface state to stay down. Unplumbing will happen when the daemon exits. This
+is done by design and is not a bug.
+
64-bit Support.
***************
-This version has been tested under Solaris 7 (and Solaris 8 Beta) in both
+This version has been tested under Solaris 7 (and Solaris 8 ) in both
32- and 64-bits environments (Ultra class machines). Installing the package
by executing "make install" will result in additional files residing in
/kernel/drv/sparcv9 and /kernel/strmod/sparcv9 subdirectories.