Set the IPv6CP restart interval (retransmission timeout) to \fIn\fR
seconds (default 3).
.TP
-.B ipx
-Enable the IPXCP and IPX protocols. This option is presently only
-supported under Linux, and only if your kernel has been configured to
-include IPX support.
-.TP
-.B ipx\-network \fIn
-Set the IPX network number in the IPXCP configure request frame to
-\fIn\fR, a hexadecimal number (without a leading 0x). There is no
-valid default. If this option is not specified, the network number is
-obtained from the peer. If the peer does not have the network number,
-the IPX protocol will not be started.
-.TP
-.B ipx\-node \fIn\fB:\fIm
-Set the IPX node numbers. The two node numbers are separated from each
-other with a colon character. The first number \fIn\fR is the local
-node number. The second number \fIm\fR is the peer's node number. Each
-node number is a hexadecimal number, at most 10 digits long. The node
-numbers on the ipx\-network must be unique. There is no valid
-default. If this option is not specified then the node numbers are
-obtained from the peer.
-.TP
-.B ipx\-router\-name \fI<string>
-Set the name of the router. This is a string and is sent to the peer
-as information data.
-.TP
-.B ipx\-routing \fIn
-Set the routing protocol to be received by this option. More than one
-instance of \fIipx\-routing\fR may be specified. The '\fInone\fR'
-option (0) may be specified as the only instance of ipx\-routing. The
-values may be \fI0\fR for \fINONE\fR, \fI2\fR for \fIRIP/SAP\fR, and
-\fI4\fR for \fINLSP\fR.
-.TP
-.B ipxcp\-accept\-local
-Accept the peer's NAK for the node number specified in the ipx\-node
-option. If a node number was specified, and non-zero, the default is
-to insist that the value be used. If you include this option then you
-will permit the peer to override the entry of the node number.
-.TP
-.B ipxcp\-accept\-network
-Accept the peer's NAK for the network number specified in the
-ipx\-network option. If a network number was specified, and non-zero, the
-default is to insist that the value be used. If you include this
-option then you will permit the peer to override the entry of the node
-number.
-.TP
-.B ipxcp\-accept\-remote
-Use the peer's network number specified in the configure request
-frame. If a node number was specified for the peer and this option was
-not specified, the peer will be forced to use the value which you have
-specified.
-.TP
-.B ipxcp\-max\-configure \fIn
-Set the maximum number of IPXCP configure request frames which the
-system will send to \fIn\fR. The default is 10.
-.TP
-.B ipxcp\-max\-failure \fIn
-Set the maximum number of IPXCP NAK frames which the local system will
-send before it rejects the options. The default value is 3.
-.TP
-.B ipxcp\-max\-terminate \fIn
-Set the maximum number of IPXCP terminate request frames before the
-local system considers that the peer is not listening to them. The
-default value is 3.
-.TP
.B kdebug \fIn
Enable debugging code in the kernel-level PPP driver. The argument
values depend on the specific kernel driver, but in general a value of
address during IPCP negotiation (unless it specified explicitly on the
command line or in an options file).
.TP
-.B noipx
-Disable the IPXCP and IPX protocols. This option should only be
-required if the peer is buggy and gets confused by requests from pppd
-for IPXCP negotiation.
-.TP
.B noktune
Opposite of the \fIktune\fR option; disables pppd from changing system
settings.
longer be transmitted on the link. It is executed with the same parameters
as the ipv6\-up script.
.TP
-.B /etc/ppp/ipx\-up
-A program or script which is executed when the link is available for
-sending and receiving IPX packets (that is, IPXCP has come up). It is
-executed with the parameters
-.IP
-\fIinterface\-name tty\-device speed network\-number local\-IPX\-node\-address
-remote\-IPX\-node\-address local\-IPX\-routing\-protocol remote\-IPX\-routing\-protocol
-local\-IPX\-router\-name remote\-IPX\-router\-name ipparam pppd\-pid\fR
-.IP
-The local\-IPX\-routing\-protocol and remote\-IPX\-routing\-protocol field
-may be one of the following:
-.IP
-NONE to indicate that there is no routing protocol
-.br
-RIP to indicate that RIP/SAP should be used
-.br
-NLSP to indicate that Novell NLSP should be used
-.br
-RIP NLSP to indicate that both RIP/SAP and NLSP should be used
-.TP
-.B /etc/ppp/ipx\-down
-A program or script which is executed when the link is no longer
-available for sending and receiving IPX packets. This script can be
-used for undoing the effects of the /etc/ppp/ipx\-up script. It is
-invoked in the same manner and with the same parameters as the ipx\-up
-script.
-.SH FILES
-.TP
.B /var/run/ppp\fIn\fB.pid \fR(BSD or Linux), \fB/etc/ppp/ppp\fIn\fB.pid \fR(others)
Process-ID for pppd process on ppp interface unit \fIn\fR.
.TP
projects / ppp.git / blobdiff