Remove files that don't go into releases

[ppp.git] / README.ultrix

diff --git a/README.ultrix b/README.ultrix
deleted file mode 100644 (file)
index b6a80d8..0000000
--- a/README.ultrix
+++ /dev/null
@@ -1,121 +0,0 @@
-
-Installing PPP on an Ultrix system requires rebuilding the kernel and
-rebooting, in addition to making and installing the pppd and chat
-programs.  These instructions apply to RISC (MIPS) systems.  This
-software should work under Ultrix 4.2, 4.3 or 4.4 (this release has
-not been tested yet).
-
-
-Kernel installation procedure.
-******************************
-
-If you have not previously had an earlier version of this package
-installed in the kernel, follow these steps:
-
-1. Become root.
-
-2. Apply the patches in the file ultrix/patches using the command:
-
-       patch -p -N <ultrix/patches
-
-This will edit the following files, saving the original versions in a
-file with `.orig' appended to the name:
-
-       /usr/sys/h/ioctl.h
-       /usr/sys/net/net/if.h
-       /usr/sys/net/net/netisr.h
-       /usr/sys/net/net/conf_net.c
-       /usr/sys/data/pseudo_data.c
-       /usr/sys/data/tty_conf_data.c
-       /usr/sys/conf/mips/files.mips
-
-Alternatively, edit these files according to the differences shown in
-ultrix/patches.
-
-3. Copy the following files to /usr/sys/io/netif:
-
-       net/ppp-comp.h
-       net/ppp_defs.h
-       ultrix/bsd-comp.c
-       ultrix/ppp-deflate.c
-       ultrix/if_ppp.c
-       ultrix/if_ppp.h
-       ultrix/if_pppvar.h
-       ultrix/ppp_tty.c
-       ultrix/slcompress.c
-       ultrix/slcompress.h
-       common/zlib.c
-       common/zlib.h
-
-4. Add a line like this to the configuration file for your kernel:
-
-       pseudo-device ppp       2
-
-The `2' indicates the number of interfaces desired.  The configuration
-file should be in /usr/sys/conf/mips.
-
-5. Rebuild your kernel.  The simplest way to do this is with the
-`doconfig' command, like this:
-
-       /etc/doconfig -c kernel-name
-
-where `kernel-name' should be replaced by the name of your kernel
-configuration file.  Alternatively, run config, cd to the compilation
-directory, and run make.
-
-6. Copy the new /vmunix to /.  It would be a good idea to keep a copy
-of your old /vmunix in / under a different name.
-
-7. Reboot the system.
-
-********
-
-If you have ppp-2.2 already installed in your kernel, most files will
-already have been modified as required.  You will need to add some
-entries to /usr/sys/conf/mips/files.mips.  You can do this with a
-command like this (as root):
-
-       patch -p -N <ultrix/upgrade
-
-Alternatively, edit /usr/sys/conf/mips/files.mips according to the
-differences shown in ultrix/upgrade.
-
-Then, proceed with steps 3, 5, 6, 7 above (step 4 should have been
-done already).
-
-
-Installing pppd and chat.
-*************************
-
-1. cd to the ppp-2.2 directory and do:
-
-       ./configure
-       make
-
-2. Become root, and do:
-
-       make install
-
-
-Credits.
-********
-
-The original port to Ultrix was done by:
-
-       Per Sundstrom 
-       DEC, Sweden
-       email: sundstrom@stkhlm.enet.dec.com
-
-and
-
-       Robert Olsson 
-       Swedish University of Agricultural Sciences
-       and also RO Komm. & Konsult
-       email: robert@robur.slu.se
-
-It was updated to ppp-2.3 by
-
-       Paul Mackerras
-       Dept. of Computer Science
-       Australian National University
-       paulus@cs.anu.edu.au