X-Git-Url: http://git.ozlabs.org/?a=blobdiff_plain;f=doc%2Fexamples%2Fyaboot.conf.rs6k;fp=doc%2Fexamples%2Fyaboot.conf.rs6k;h=0000000000000000000000000000000000000000;hb=678d83ff8608534ece0f1e912eddedef4f0bb67a;hp=b9f9a4450522c1beffc3a2cacad8b6dfe2bc6897;hpb=9323f7c29a886304325b1562450729a12e0ccbea;p=yaboot.git

diff --git a/doc/examples/yaboot.conf.rs6k b/doc/examples/yaboot.conf.rs6k
deleted file mode 100644
index b9f9a44..0000000
--- a/doc/examples/yaboot.conf.rs6k
+++ /dev/null
@@ -1,72 +0,0 @@
-## Example yaboot.conf for ybin and yaboot >= 0.6
-## see man yaboot.conf for more details.
-
-## Change `unconfigured' to your bootstrap partition ie: /dev/hda2
-boot=unconfigured
-
-## fstype=raw is what makes ybin dd yaboot to the bootstrap partition
-## instead of using a filesystem. 
-
-fstype=raw
-
-## device is the OpenFirmware device path to the disk containing
-## kernel images.  if your disk is /dev/hda you can find the
-## OpenFirmware path by running the command: ofpath /dev/hda DO NOT
-## specify a partition number for this!  This is generally not
-## necessary for IBM hardware
-
-#device=hd:
-
-## partition is the partition number where the kernel images are
-## located.  The kernel images should be on your root filesystem, so
-## this is usually the same partition number as your root filesystem.
-## so if root = /dev/hda3 (the 3rd partition) then you should have
-## partition=3  This *MUST* be set correct or yaboot won't boot!  This
-## option can be either set globally as shown here, or per image in
-## the image= sections
-
-partition=3
-
-## timeout is the amount of time in tenths of a second that yaboot
-## will wait before booting the default kernel image (the first image=
-## section in this config file or the value of default=).  
-
-timeout=20
-install=/usr/local/lib/yaboot/yaboot
-
-## nonvram is required for IBM hardware currently since ofpath does
-## not support them, it is also probably not necessary.
-
-nonvram
-
-## Password supplied in plaintext, required for yaboot to boot, unless
-## restricted is also present (see below).  Be sure to
-## chmod 600 /etc/yaboot.conf if you set this!
-
-#password=secret
-
-## Password supplied as an md5 hash, see above
-
-#password=$1$saltstri$WHZcnT3IOdSrMvizOq7Ht1
-
-## A password is only required to boot an image specified here if
-## parameters are specified on the command line or if the user enters
-## an image is not specified in the configuration file at all (ie.
-## arbitrary file load).  restricted can also be placed in an image
-## section in that case any image not including the restricted keyword
-## will be fully password protected.
-
-#restricted
-
-## image is the kernel itself, commonly kept in / but also commonly
-## found in /boot.  Note that /boot should generally not be its own
-## partition on powerpcs, its not necessary and complicates things.
-## Make sure /boot is on the partition specified by partition= see
-## above.  /boot should never be an HFS filesystem.  You may point
-## image= to a symbolic link so long as the symlink does not cross
-## partition boundries.
-
-image=/vmlinux
-	label=Linux
-	root=/dev/sda3
-	read-only